濰坊電梯門套:不銹鋼電梯門套是什么東西 如何安裝不銹鋼電梯門套
不銹鋼電梯門套常用的不銹鋼板材分為201和304兩種型號,實際上是成分不同,304質量好一些,但貴,201差一些,但作為家用也完全能滿足需要。另外板材厚度也不同,一般商實際后的0.6的就足夠了。板材表面處理也分為鏡面和油膜拉絲兩種,工裝一般建議用鏡面不銹鋼,油膜拉絲的效果差一些。
The commonly used stainless steel plates for elevator door frames are divided into two types: 201 and 304. In fact, the composition is different. 304 has better quality, but it is more expensive. 201 is slightly inferior, but it can fully meet the needs of household use. In addition, the thickness of the board is also different. Generally, a practical 0.6 is sufficient. The surface treatment of sheet metal can also be divided into two types: mirror finish and oil film drawing. Generally, mirror finish stainless steel is recommended for tooling, but the effect of oil film drawing is relatively poor.
如何安裝不銹鋼電梯門套
How to install stainless steel elevator door frames
1、校對洞口
1. Proofread hole
洞口尺寸是否符合安裝要求,不符合要求應予以必要的處理。
Whether the size of the opening meets the installation requirements, and if it does not meet the requirements, necessary treatment should be taken.
2、拆包檢查
2. Unpacking inspection
檢查門框、門套線、擋門條、密封條,零部件是否齊。
Check if the door frame, door frame line, door stop strip, sealing strip, and components are complete.
3、組裝門框
3. Assembling door frames
門框組裝時豎框與橫框搭接處必須涂膠,然后用自攻絲予以固定。
When assembling the door frame, the overlap between the vertical and horizontal frames must be coated with glue, and then fixed with self tapping screws.
4、定位門框
4. Positioning the door frame
門框按室內標高線就位,先用木楔從門框周圍夾緊門框,再用工裝和木楔從門框內口撐緊門框,通過夾門框內外木楔,調整門框豎直度、水平度及門框內徑尺寸,使其達到設計要求。
The door frame is positioned according to the indoor elevation line. First, use wooden wedges to clamp the door frame around it, and then use fixtures and wooden wedges to support the door frame from the inner opening. By clamping the wooden wedges inside and outside the door frame, adjust the verticality, levelness, and inner diameter of the door frame to meet the design requirements.
5、門框注膠
5. Door frame gluing
門框與墻體間填充發泡膠前要清理干凈墻體,用噴壺濕潤墻面,填充發泡膠,注意發泡膠填充要適量,多余發泡膠用刀片切平。
Before filling the gap between the door frame and the wall with foam adhesive, the wall should be cleaned thoroughly, moistened with a spray can, and filled with foam adhesive. Pay attention to filling the foam adhesive in an appropriate amount, and use a blade to cut off excess foam adhesive.
6、做好門套
6. Make good door frames
將不銹鋼按照設計要求裁剪出來,做成一個門套,
Cut the stainless steel according to the design requirements and make it into a door frame,
6、安裝門套線
6. Install door frame wire
待4-6小時發泡膠固化后,卸下工裝和木楔,在門框嵌槽內涂膠,然后將門套線嵌入門框,輕輕敲緊壓實使門套線與墻體緊密貼合。
After 4-6 hours of curing of the foam adhesive, remove the tooling and wooden wedge, apply adhesive to the embedded groove of the door frame, and then embed the door frame line into the door frame. Gently tap and compact to make the door frame line tightly adhere to the wall.
7、安裝門扇
7. Install door leaf
注意門的開啟方向,安裝五金,門扇與門框間隙達到設計要求,保證門扇開關靈活。
Pay attention to the opening direction of the door, install hardware, and ensure that the gap between the door leaf and the door frame meets the design requirements, ensuring that the door leaf switches flexibly.
本文由 濰坊電梯門套 友情奉獻.更多有關的知識請點擊 http://www.zjy168.com 真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This article is dedicated to the friendship of Weifang elevator door frames. For more related knowledge, please click http://www.zjy168.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned